0 Cart
In Stock
Price

Product filters

In Stock
Price

$  –  $

  • $2
  • $160

Other Tools

Sort by Popularity
128 Per Page
AK Trunnion Rivet Hole Drilling Fixture
Quick view
$99.95
AK Trunnion Rivet Hole Drilling Fixture
Here is a professional tool for drilling the front and rear trunnion holes in AK47 receivers.  This tool will work with 7.62 and 5.45 trunnions...
In Stock
Select options
AK-BUILDER Receiver Blank Drilling Fixture
Quick view
$159.95
AK-Builder Receiver Blank Drilling Fixture
V-4 For 1.5mm Receivers
AK-BUILDER Receiver Blank Drilling Fixture This tool is designed to be used with 80% receivers with OR without rails and center supports...
In Stock
 
Select an option
5MM & 7MM REAMER SET, A2-31
Quick view
$36.95
5mm & 7mm Reamer Set
 5mm and 7mm reamers for finishing the hammer and trigger holes on my flats. These will ensure that you have perfectly round holes for the axis pins to...
In Stock
+ −
AK-Builder Rail Alignment Fixture
Quick view
$29.95
AK-Builder Rail Alignment Fixture
Rail alignment fixture to install the lower bolt guide rails in stamped receivers. The rails clamp inside the fixture which inserts into the trunnion to...
In Stock
+ −
GREEN CHINESE RIVET DRILLING MANDREL, R2-13
Quick view
$19.95
Green Chinese Rivet Drilling Mandrel
This will fit the smaller diameter Chinese trunnions. Does NOT come with bolt.
In Stock
+ −
RIVET HEAD DRILLING TOOL, B6-31
Quick view
$37.95
Rivet Head Drilling Tool
This tool is made for removing the trunnion rivets off of parts kits or removing rivets that we sell.  Made of steel then heat treated for wear...
In Stock
+ −
.300 BARREL PIN REAMER, A2-32
Quick view
$32.95
.300 Barrel Pin Reamer
This is the same reamer we use to work with the .302 barrel pin holes.  Drill the hole first with a 7mm drill then ream the hole.  The reamer has...
+ −
AK-BUILDER FRONT SIGHT & GAS BLOCK SUPPORT, C8-11
Quick view
$29.95
AK-Builder Front Sight & Gas Block Support
Here is a tool that we have been using to demill and populate our parts kits.  This is made to support the AKM gas block and front sight while...
In Stock
+ −
Cobalt Gas Port Drill for Bulgarian AK74's
Quick view
$4.95
Cobalt Gas Port Drill for Bulgarian AK74's
This drill is .076" and the original port size is .077". More than likely with a cheap drill press or hand drill the bit will cut oversize so it won't...
+ −
AKFST Heavy Duty Front Sight Tool
Quick view
$38.95
AKFST Heavy Duty Front Sight Tool
The AKFST line of AK-47 front sight tools are the first AK front sight tool to be made to the levels of strength and durability the AK end user or...
In Stock
+ −
AKM TRUNNION SUPPORT BLOCK, C8-21
Quick view
$32.50
AKM Trunnion Support Block
Support plate for pressing in or out your barrel pins on an AKM style trunnion.  These are not specifically made for use with any of the bulged...
In Stock
+ −
Gas Piston Drilling Jig
Quick view
$37.95
Gas Piston Drilling Jig
Used for drilling the gas piston rivet hole in the center of the piston.
In Stock
+ −
PSL Brass Barrel Press Puck
Quick view
$9.95
PSL Brass Barrel Press Puck
The PSL Brass Barrel Press Puck is used to press the PSL barrel out of the front trunnion. DO NOT use the other brass nut we sell for the other barrels we...
In Stock
+ −
12mm x 1.25mm Gas Piston Tap
Quick view
$12.95
12mm x 1.25mm Gas Piston Tap
12mm x 1.25mm tap for cleaning up the threads on the bolt carrier when installing a new gas piston. Made of high speed steel for long life.
In Stock
+ −
AK-BUILDER SIGHT & GAS BLOCK PIN PUNCH SET, B6-51
Quick view
$49.95
Ak-Builder Sight & Gas Block Pin Punch Set
We designed these punches for demilling parts kits in our shop and use them daily. These can be bought as a set or individually.  The set comes with a...
In Stock
+ −
DIE STARTER 14-1 LH, A4-11
Quick view
$15.00
Die Starter 14-1 LH
Die Starter for 14-1 LH 7.62x39 rifles.
In Stock
+ −
BULGED FRONT TRUNNION SUPPORT BLOCK, C11-21
Quick view
$27.50
Bulged Front Trunnion Support Block
Support plate for pressing in or out your barrel pins on 1.5mm bulged receivers.  These are also used for demilling your front and rear trunnions on...
In Stock
+ −
MILLED Receiver Drilling Fixture
Quick view
$119.95
MILLED Receiver Drilling Fixture V2
AK-BUILDER Milled Receiver Drilling Fixture This tool is made specifically for the AK-BUILDER 80% Milled Receivers. We can not guarantee this fixture...
In Stock
+ −
One Inch Capacity C-Clamp
Quick view
$2.75
One Inch Capacity C-Clamp
Small C-Clamp for installing the lower rails in your receiver or for clamping the scribe jig to the bent receiver to mark the cutouts of the top rail.
+ −
Two Inch Capacity C-Clamp
Quick view
$3.95
Two Inch Capacity C-Clamp
Two inch C-Clamp for clamping trunnions for test fitting parts to your rifle before final installation.
In Stock
+ −
AK-BUILDER 3MM STARTER PIN PUNCH, N-11
Quick view
$9.95
Ak-Builder 3mm Starter Pin Punch
This punch is used for the 3mm pins on standard gas blocks and front sights. We designed these punches for demilling parts kits in our shop and use them...
In Stock
+ −
AK-BUILDER 3MM FINISH PIN PUNCH, N-12
Quick view
$9.95
Ak-Builder 3mm Finish Pin Punch
This punch is used for the 3mm pins on standard gas blocks and front sights once it has started to move using another punch.  Using the long punch to...
In Stock
+ −
AK-BUILDER 4MM STARTER PIN PUNCH, N-13
Quick view
$9.95
Ak-Builder 4mm Starter Pin Punch
We designed these punches for demilling parts kits in our shop and use them daily. These can be bought as a set or individually.  The problem with...
In Stock
+ −
CHINESE GAS PORT CLEANING TOOL, G4-61
Quick view
$2.25
Chinese Gas Port Cleaning Tool
This tool if for cleaning the gas port in the gas block of AK47's with 45 degree gas blocks.  Original Chinese surplus.
In Stock
+ −
AK-BUILDER 4MM MEDIUM PIN PUNCH, N-14
Quick view
$9.95
Ak-Builder 4mm Medium Pin Punch
This punch is used for the 4mm pin in the rear sight if it is still tight after using the starter punch. We designed these punches for demilling parts...
In Stock
+ −
AK-BUILDER 4MM FINISH PIN PUNCH, N-15
Quick view
$9.95
Ak-Builder 4mm Finish Pin Punch
This punch is used for the 4mm pin to drive it completely out of the rear sight.  It is best to use a starter length punch to get the pin to move...
In Stock
+ −
7/16 WRENCH, M-23
Quick view
$5.95
7/16 Wrench
This wrench is for use with our pin punches to hold the punch in place to keep from hitting your hand when starting stubborn gas block/front sight pins.
In Stock
+ −
2.5mm Punch Set
Quick view
$27.95
2.5mm Punch Set
We designed these punches for demilling parts kits in our shop and use them daily. These can be bought as a set or individually. The...
In Stock
+ −
2.5mm Punch
Quick view
$14.95
2.5mm Punch
This punch is used for the 2.5mm pins on yugo gas blocks and front sights. We designed these punches for demilling parts kits in our...
In Stock
+ −
2.5mm Starter Punch
Quick view
$14.95
2.5mm Starter Punch
This punch is used for the 2.5mm pins on yugo gas blocks and front sights. We designed these punches for demilling parts kits in our...
In Stock
+ −
  • Out of stock
HANDGUARD RETAINER & GAS TUBE LEVER WRENCH, A3-51
Quick view
$15.99
Handguard retainer & gas tube lever wrench
Made to ease the removal and installation of the gas tube and handguard of your AK47.
No products with the selected options in stock
AK-BUILDER FRONT SIGHT ELEVATION TOOL - KEYCHAIN, C2-51
Quick view
$19.95
AK-Builder Front Sight Elevation Tool - Keychain
The AK-Builder Front Sight Elevation Tool is made from 4130 steel.  We then sent it out for nitride to not only give it a nice black coat, but also strength....
In Stock
+ −
CIRCLE 7 ARMORY SIGHT LEAF TOOL, C10-61
Quick view
$29.99
Circle 7 Armory Sight Leaf Tool
New from Circle 7 Armory comes a sight leaf tool to help one of the more stubbon aspects of AK work! Just secure the tool underneath the gas tube latch...
In Stock
+ −