0 Cart

Product filters

In Stock
Price

$  –  $

  • $7
  • $700
Receiver Thickness

Receiver Flats

AK-Builder Flat

Our receiver flats have been the standard go-to flats for years.  All flats are made with 4130 steel for the best results for heat treating.

Top Rail Fit

$7.00
These are made from heat treated 4130 steel and the rivets are a copy of an original AK center support rivet. The length is shorter than the 1mm center...
In Stock

$10.95
Get a set of the best US made rails available! These have mag stabilizers on both rails unlike any other rails made in the US.There are no holes drilled in...
In Stock

$14.95
This is a new design that matches the original plates.  Orders shipped after 9/5/2015 will have the newer design. These are not needed on the Yugo's...
In Stock

$14.95
These new plates have been made from the dimensions of original demilled Russian and Bulgarian plates. This plate welds to the rear lower section of...
In Stock

  • Save 18%
SAIGA 12 RUSSIAN EXTENDED REINFORCEMENT PLATE, A2-43
$17.95 $21.95
This is for the longer Russian pistol grip to fit on the Saiga 12.  The Hogue pistol grip is longer than standard and uses this same plate. Pistol grip...
In Stock

$44.95
With Y & I Embossing, 1mm
Now with Y & I embossing! These flats can be used for about any 1mm thick 7.62 receiver.  Without the trunnion holes you can put any rear...
In Stock
 

$45.95
With Y & I Embossing, 1mm
This flat has the magwell and mag dimples to match the 5.45 magazines which are narrower then 7.62 mags.  There are no front or rear trunnion holes....
In Stock
 

$46.95
With Y & I Embossing, 1mm
The front and rear trunnion holes on these flats are pre-punched to help with the installation of the trunnions.  In some cases the front trunnion...
In Stock
 

  • Out of stock
Bulgarian Sidefolder AK74SU 5.45 Flat
$49.95
With Y & I Embossing, 1mm
This flat was made for the Bulgarian style sidefolding triangle or polymer stock.  The magwell and magwell dimples are made to fit 5.45...
 
No products with the selected options in stock

$54.95
1.27mm
This is our MAK90 flat with top rails machined and mag well dimples. These come with lower bolt guide rails. Due to the dimensional differences between...
In Stock

$57.50
1.5mm
Finally there is an alternative to the home builder to make your own professional grade 1.5mm receiver from a flat.  The material these are made...
In Stock

$57.50
1.5mm
Finally there is an alternative to the home builder to make your own professional grade 1.5mm receiver from a flat. The material these are made from is .063...
In Stock

$57.50
1.5mm
Finally there is an alternative to the home builder to make your own professional grade 1.5mm receiver from a flat. The material these are made from is .063...
In Stock

$57.50
1.5mm
This is the 1.5mm 4130 flat and rails for the M85 kits that are out.  It's basically just our standard M70 underfolder flat without the pin holes cut...
In Stock

$58.50
1.5mm
These flats are for the bulged trunnion RPK 47 7.62 parts kits.  The flats and rails are made from 4130 and are in the soft annealed condition and need...
In Stock

  • Out of stock
MAK 90 UNDERFOLDER FLAT WITH MAGWELL DIMPLES, B1-41
$58.95
THIS REQUIRES OUR MODIFIED MAK90 PUNCH TO BEND CORRECTLY. IF YOU USE OUR OLD PUNCH IT WILL RUIN THE FLAT! WE HAD TO MODIFY THE MAK90 PUNCH TO ACCOMADATE...
No products with the selected options in stock