0 Cart

Product filters

In Stock
Price

$  –  $

  • $7
  • $700
Receiver Thickness

Receiver Flats

AK-Builder Flat

Our receiver flats have been the standard go-to flats for years.  All flats are made with 4130 steel for the best results for heat treating.

Top Rail Fit

$57.50
1.5mm
This is the 1.5mm 4130 flat and rails for the M85 kits that are out.  It's basically just our standard M70 underfolder flat without the pin holes cut...
In Stock

$57.50
1.5mm
Finally there is an alternative to the home builder to make your own professional grade 1.5mm receiver from a flat. The material these are made from is .063...
In Stock

$57.50
1.5mm
Finally there is an alternative to the home builder to make your own professional grade 1.5mm receiver from a flat. The material these are made from is .063...
In Stock

$57.50
1.5mm
Finally there is an alternative to the home builder to make your own professional grade 1.5mm receiver from a flat.  The material these are made...
In Stock

$14.95
This is a new design that matches the original plates.  Orders shipped after 9/5/2015 will have the newer design. These are not needed on the Yugo's...
In Stock

$14.95
These new plates have been made from the dimensions of original demilled Russian and Bulgarian plates. This plate welds to the rear lower section of...
In Stock

$44.95
With Y & I Embossing, 1mm
Now with Y & I embossing! These flats can be used for about any 1mm thick 7.62 receiver.  Without the trunnion holes you can put any rear...
In Stock
 

  • Save 18%
SAIGA 12 RUSSIAN EXTENDED REINFORCEMENT PLATE, A2-43
$17.95 $21.95
This is for the longer Russian pistol grip to fit on the Saiga 12.  The Hogue pistol grip is longer than standard and uses this same plate. Pistol grip...
In Stock

$59.95
With Y & I Embossing, 1mm
    These are made to work with the Romanian underfolder stocks and will not work with the Polish or Yugo sets.  There is no need to...
In Stock
 

$58.50
1.5mm
These flats are for the bulged trunnion RPK 47 7.62 parts kits.  The flats and rails are made from 4130 and are in the soft annealed condition and need...
In Stock

  • Product is running out
REFURBISHED ROMANIAN FIXED STOCK 7.62X39 PARTS KIT  (NO FURNITURE), KIT-26R
$639.95
We did the hard part for you! With this complete refurbish of parts from a matching numbers 7.62x39 Romanian fixed stock. Each piece has been acid dipped...
In Stock

$59.95
With Y & I Embossing, 1mm
The Polish Underfolder is the most popular underfolder parts kit and this was the first specialty flat that I had perfected by modifying existing flats in...
In Stock
 

$59.95
With Y & I Embossing, 1mm
This flat is specifially made for the Polish Tantal to work with the left side selector and right side safety.  The hole for the selector/safety is a...
In Stock
 

  • Out of stock
MAK 90 UNDERFOLDER FLAT WITH MAGWELL DIMPLES, B1-41
$58.95
THIS REQUIRES OUR MODIFIED MAK90 PUNCH TO BEND CORRECTLY. IF YOU USE OUR OLD PUNCH IT WILL RUIN THE FLAT! WE HAD TO MODIFY THE MAK90 PUNCH TO ACCOMADATE...
No products with the selected options in stock

  • Out of stock
M92 UNDERFOLDER TRUNNION FLAT, B1-31Y
$59.95
With Y & I Embossing, 1mm
This flat will work with the M92 or M70 that has the flat sided front trunnion . These will NOT WORK with the bulged RPK style trunnions.  ...
 
No products with the selected options in stock

$59.95
With Y & I Embossing, 1mm
THESE DO NOT HAVE ALIGNMENT HOLES IN THEM ANYMORE The AMMS trunnions I have seen are machined unlike the Polish which are stamped and welded...
In Stock