Welcome to ak-builder.com!

Drills and Taps

$2.85
Material: HSS Screw Machine - Drills Size: 0.1181 In 3.00 mm Flute Length: 5/8, 16 mm Overall Length: 1-13/16, 46 mm Finish/Coating: Black...
In Stock
+
Add to wish list

$2.95
These are the same drills I use in the Rivet Drilling tool, drilling gas piston rivet holes and for drilling holes for the 4mm rivet holes in receivers....
In Stock
+
Add to wish list

$3.29 $2.95
HSS Screw Machine - Drills Size: 0.1575 In., 4.00 mm Flute Length: 7/8, 22 mm Overall Length: 2-5/32, 55 mm Finish/Coating: Black Oxide Point...
In Stock
+
Add to wish list

$2.95
Replacement drill bit for our milled receiver drilling fixture. Used to drill the selector stop hole and for drilling the trigger hole before...
In Stock
+
Add to wish list

$3.25
This drill is used for drilling holes for the 4.5mm rivet holes in the bent receivers as well as opening the hammer pin hole on my flats before reaming to...
In Stock
+
Add to wish list

$3.25
#21 Screw Machine Drill Bit
In Stock
+
Add to wish list

$3.75
This drill is .076" and the original port size is .077". More than likely with a cheap drill press or hand drill the bit will cut oversize so it won't...
In Stock
+
Add to wish list

$4.25
HSS Screw Machine - Drills Size: 0.1969 In., 5.00 mm Flute Length: 1-1/32, 26 mm Overall Length: 2-7/16, 62 mm Finish/Coating: Black Oxide...
In Stock
+
Add to wish list

$4.50
This drill bit is for drilling the front edge of the keyhole for the selector on the right side of the receiver. US Made by Precision Twist Drill....
In Stock
+
Add to wish list

$4.65
2.5mm Screw Machine Drill Bit
In Stock
+
Add to wish list

$4.95
These are the drill bits I use for drilling 7.62 gas ports.  These will fit into the port and it will guide the drill.  Just press the gas block on first....
In Stock
+
Add to wish list

$4.95
6mm screw machine drill bit. This is used for drilling the hole in the bottom of a reciever when installing the latch assembly for the triangle side folding...
In Stock
+
Add to wish list

$5.25
US Made by Precision Twist Drill Screw Machine - Drills Size: 0.2756 In., 7.00 mm Flute Length: 1-11/32, 34 mm Overall Length: 2-29/32, 74 mm...
In Stock
+
Add to wish list

$9.95
This drill bit is for drilling the large selector hole on the right side of the receiver. This makes the larger side of the keyhole.  Get our 7/32 drill...
In Stock
+
Add to wish list

$10.95
This is used with our 12-1.25 dies sold on the website.
In Stock
+
Add to wish list

$12.95
12mm x 1.25mm tap for cleaning up the threads on the bolt carrier when installing a new gas piston. Made of high speed steel for long life.
In Stock
+
Add to wish list

$15.00
Die Starter for 14-1 LH 7.62x39 rifles.
Out-of-stock Add to wish list

$20.50
This die will fix damaged threads on gas pistons as well as put new threads on custom made pistons.
In Stock
+
Add to wish list

$25.00
This is the same reamer we use to work with the .302 barrel pin holes.  Drill the hole first with a 7mm drill then ream the hole.  The reamer has more...
In Stock
+
Add to wish list

$25.00
Use this reamer for the .315 oversize barrel pins.  Start with the hole drilled at 7mm then switch to the reamer.
In Stock
+
Add to wish list

$32.45
 5mm and 7mm reamers for finishing the hammer and trigger holes on my flats. These will ensure that you have perfectly round holes for the axis pins to go...
In Stock
+
Add to wish list

$37.95
This tool is made for removing the trunnion rivets off of parts kits or removing rivets that we sell.  Made of steel then heat treated for wear...
In Stock
+
Add to wish list