0 Cart

Product filters

In Stock
Price

$  –  $

  • $2
  • $38

Drills and Taps

$6.45
These are the drill bits I use for drilling 7.62 gas ports.  These will fit into the port and it will guide the drill.  Just press the gas block...
In Stock

$36.95
 5mm and 7mm reamers for finishing the hammer and trigger holes on my flats. These will ensure that you have perfectly round holes for the axis pins to...
In Stock

$6.25
US Made by Precision Twist Drill Screw Machine - Drills Size: 0.2756 In., 7.00 mm Flute Length: 1-11/32, 34 mm Overall Length: 2-29/32, 74 mm...

$3.65
Material: HSS Screw Machine - Drills Size: 0.1181 In 3.00 mm Flute Length: 5/8, 16 mm Overall Length: 1-13/16, 46 mm Finish/Coating: Black...

$32.95
This is the same reamer we use to work with the .302 barrel pin holes.  Drill the hole first with a 7mm drill then ream the hole.  The reamer has...

$2.95
These are the same drills I use in the Rivet Drilling tool, drilling gas piston rivet holes and for drilling holes for the 4mm rivet holes in receivers....

$4.65
HSS Screw Machine - Drills Size: 0.1575 In., 4.00 mm Flute Length: 7/8, 22 mm Overall Length: 2-5/32, 55 mm Finish/Coating: Black Oxide Point...

$37.95
This tool is made for removing the trunnion rivets off of parts kits or removing rivets that we sell.  Made of steel then heat treated for wear...
In Stock

$3.95
This drill is used for drilling holes for the 4.5mm rivet holes in the bent receivers as well as opening the hammer pin hole on my flats before reaming to...

$4.25
HSS Screw Machine - Drills Size: 0.1969 In., 5.00 mm Flute Length: 1-1/32, 26 mm Overall Length: 2-7/16, 62 mm Finish/Coating: Black Oxide...

$25.00
Use this reamer for the .315" (8mm) oversize barrel pins.  Start with the hole drilled at 7mm then switch to the reamer.

$3.75
This drill is .076" and the original port size is .077". More than likely with a cheap drill press or hand drill the bit will cut oversize so it won't...

$9.95
This drill bit is for drilling the large selector hole on the right side of the receiver. This makes the larger side of the keyhole.  Get our 7/32...

$4.50
This drill bit is for drilling the front edge of the keyhole for the selector on the right side of the receiver. US Made by Precision Twist Drill....

$3.65
2.5mm Screw Machine Drill Bit
In Stock

$15.00
Die Starter for 14-1 LH 7.62x39 rifles.
In Stock

$12.95
12mm x 1.25mm tap for cleaning up the threads on the bolt carrier when installing a new gas piston. Made of high speed steel for long life.
In Stock

$3.95
#21 Screw Machine Drill Bit

$10.95
This is used with our 12-1.25 dies sold on the website.
In Stock

$4.95
6mm screw machine drill bit. This is used for drilling the hole in the bottom of a reciever when installing the latch assembly for the triangle side folding...
In Stock

  • Save 19%
FRONT SIGHT-GAS BLOCK DRILL BIT FOR VIRGIN PARTS KITS #32, C3-21
$3.65 $4.50
We use these drill bits when populating virgin parts kits without a pre-drilled hole in the gas block and front sight block that have never been drilled...

$4.95
We use these drill bits when populating virgin parts kits without a pre-drilled hole in the trunnion for the barrel pin. Tool Material  ...

$20.50
This die will fix damaged threads on gas pistons as well as put new threads on custom made pistons.
In Stock

$3.95
Replacement drill bit for our milled receiver drilling fixture. Used to drill the selector stop hole and for drilling the trigger hole before...
In Stock