0 Cart

AK-Builder Flat Bending Die Set

Write a review
1mm
In Stock
$219.95
+ −
Add to wish list
AK-Builder Flat Bending Die Set: machined steel punch, alignment pins, receiver flat, and base.

AK-Builder Flat Bending Die Set

$219.95

AK-Builder Flat Bending Die Set

A heavy-duty die set built for forming AK receiver flats in 1.0 mm, 1.5 mm, and Chinese variants (when the correct punch is used). The base starts as a solid 17 lb steel block and is precision machined down to about 14.5 lb, giving it the strength and rigidity needed for consistent, accurate forming.

The die features a radius entry to reduce press force during bending, and built-in alignment pins in the punch make setup simple and repeatable. The pins can be adjusted up or down for proper 7.62 or 5.45 magwell spacing.

There are three available punches — 1.0 mm, 1.5 mm, and Chinese — each with a different internal dimension but the same outer dimension, so the base works with any punch as long as the proper flat is used.

Designed for use with a 12-ton shop press or larger, this set delivers precision results and long service life.

Key Features

  • Machined steel base (~14.5 lb finished) for strength and rigidity

  • Radius entry for smoother bends with less pressure

  • Built-in adjustable alignment pins for accurate bends on 7.62 or 5.45 flats

  • Works with 1.0 mm, 1.5 mm, and Chinese punches (shared base design)

  • Lower die set screws aid in removing punch and flat after pressing

  • Compatible with 12-ton presses or larger

  • For lower bend only — does not form upper rails

Compatibility & Notes

  • MAK90 punch update (Oct. 19, 2018): Punches with serial 7310 or higher are compatible with the new MAK90 underfolder flats. Older punches (<7310) will damage those flats.

  • All punches share the same external dimensions, allowing them to work with the same die base when used with the correct flat.

  • Designed for repeated shop use.

Options:
1mm or .040" Punch
AK-Builder Barrel Press Kit components: black oxided rams, brass block, and trunnion blocks.
Quick view
$132.45
AK-Builder Barrel Press Kit
1" Ram
Choose the ram size of your press in the drop down box below. The 1" and 1.6" ram pieces are machined on a lathe from bar stock then black oxided. ...
T6-11
In Stock
 
Select an option
AK-Builder Trigger Guard Riveting Jig, black oxide finish, with detached components.
Quick view
$85.00
AK47 Trigger Guard Riveting Jig

Installs all five trigger guard rivets with precision—front four at once, rear separately. Magnetic rear support and an adjustable/removable rear block fit multiple AK variants; compatible with receivers that already have center support and rails.

T1-11
In Stock
+ −
AK-Builder riveting press, black-finished, showing main unit, assorted dies and supports.
Quick view
$270.00
AK-Builder Rivet Tool

The AK-Builder Riveting Tool is the proven standard for precision AK builds. It installs front and rear trunnion rivets, center supports, and scope rails with perfect alignment and professional results — crafted from heat-treated 4140 steel and trusted by builders worldwide. (Does not install trigger guard rivets.)

T5-11
In Stock
+ −
Angled view of AK-Builder steel Rail Alignment Fixture showing front clamp and screw.
Quick view
$29.95
AK-Builder Rail Alignment Fixture

AK-Builder rail alignment fixture — positions and clamps lower bolt guide rails in stamped receivers for accurate welding and alignment.

C3-61
In Stock
+ −
AK-Builder AK Trunnion Rivet Hole Drilling Fixture with red 7.62mm and blue 5.45mm mandrels.
Quick view
$99.95
AK Trunnion Rivet Hole Drilling Fixture
Here is a professional tool for drilling the front and rear trunnion holes in AK47 receivers.  This tool will work with 7.62 and 5.45 trunnions...
T3-11
In Stock
 
Select an option
Angled view of two uncoated high-speed steel 5mm and 7mm reamers for AK receiver pins.
Quick view
$44.95
5mm & 7mm Reamer Set

5 mm and 7 mm reamer set for finishing AK hammer and trigger pin holes. Use slow speed with cutting oil.

A2-31
In Stock
+ −

No reviews found

Customers Also Bought

Angled view of AK-Builder steel Rail Alignment Fixture showing front clamp and screw.
AK-Builder Rail Alignment Fixture
$29.95
AK-Builder Bulgarian-style center support sleeve and rivet for 1mm receivers, heat treated alloy steel.
AK Center Support for 1mm Receivers
$7.00
Angled view of two uncoated high-speed steel 5mm and 7mm reamers for AK receiver pins.
5mm & 7mm Reamer Set
$44.95
AK-Builder AK47 7.62 receiver flat, 4130 annealed, in the white, with pre-punched trunnion holes.
AK47 7.62 Flat With Trunnion Holes
$46.95
Select an option
AK-Builder AK Trunnion Rivet Hole Drilling Fixture with red 7.62mm and blue 5.45mm mandrels.
AK Trunnion Rivet Hole Drilling Fixture
$99.95
Select an option
AK-Builder AK Rivet Set, black oxide coated, showing various lengths and head styles.
AK-Builder AK Rivet Set
$14.00
Select an option
Y & I Optional Embossing
Standard AK47 Fixed Stock 7.62 Flat
$44.95
Select an option
AK-Builder Trigger Guard Riveting Jig, black oxide finish, with detached components.
AK47 Trigger Guard Riveting Jig
$85.00
AK-Builder Barrel Press Kit components: black oxided rams, brass block, and trunnion blocks.
AK-Builder Barrel Press Kit
$139.95
Select an option
AK-Builder riveting press, black-finished, showing main unit, assorted dies and supports.
AK-Builder Rivet Tool
$270.00
Close-up of AK-Builder Spot Welder Tong with screw-on tip welding an AK receiver rail.
Spot Welder Tong
$39.95
AK-Builder AK74 5.45x39 receiver flat, 4130 annealed, in the white, with 5.45 magwell dimples.
AK74 5.45x39 Fixed Stock Receiver Flat
$45.95
Select an option