0 Cart

AK-Builder Flat Bending Die Set

Write a review
1mm - 1.5mm
In Stock
$284.95
+ −
Add to wish list
AK-Builder Flat Bending Die Set

AK-Builder Flat Bending Die Set

$284.95

 The base of this die set is made from a solid piece of steel that starts off at 17lbs and is machined to 14.5lbs.  There is a radius at the entrance of the die which takes less pressure to make the bend.  In my testing I have bent several flats by just putting the ram in the middle of the punch and pressing the flat straight in without moving the ram down the length of the punch.

Once the flat is pressed in there are set screws in the lower die that will be used to remove the flat and punch assembly from the lower die. This die set will NOT bend the upper rails into the receiver.

OUR MAK90 PUNCH HAS BEEN UPDATED AS OF OCTOBER 19TH 2018!! PLEASE MAKE SURE YOU HAVE THE PROPER MAK90 PUNCH BEFORE USING IT ON OUR NEW MAK90 UNDER FOLDER FLATS!

How to tell if your Mak90 punch will work with our new Mak90 Under folder Flats.

All of our flat bending die punches have a serial number on them. If the serial number on your Chinese Mak90 punch is "7310" OR GREATER then you have the proper punch for the new Mak90 under folder flats. If your number is LESS THAN "7310" then you will ruin the Mak90 under folder flat. You will need to place an order and purchase the new punch from here. If you already have one of our punch sets make sure you LOG INTO your account so that you can purchase the new punch.

 

Options:
1mm and 1.5mm add $65
AK-Builder Barrel Press Kit
Quick view
$132.45
AK-Builder Barrel Press Kit
1" Ram
Choose the ram size of your press in the drop down box below. The 1" and 1.6" ram pieces are machined on a lathe from bar stock then black oxided. ...
T6-11
In Stock
 
Select an option
AK47 TRIGGER GUARD RIVETING JIG, T1-11
Quick view
$85.00
AK47 Trigger Guard Riveting Jig
This jig will install the five trigger guard rivets. The front four rivets can be set at once and the rear will be done separately. There is a magnet that...
T1-11
In Stock
+ −
AK-Builder Rivet Tool
Quick view
$270.00
AK-Builder Rivet Tool
THIS WILL INSTALL THE FRONT/REAR TRUNNION RIVETS AND CENTER SUPPORTS .  It will not install the trigger guard rivets. Are you ready for a...
T5-11
In Stock
+ −
AK-Builder Rail Alignment Fixture
Quick view
$29.95
AK-Builder Rail Alignment Fixture
Rail alignment fixture to install the lower bolt guide rails in stamped receivers. The rails clamp inside the fixture which inserts into the trunnion to...
C3-61
In Stock
+ −
AK Trunnion Rivet Hole Drilling Fixture
Quick view
$99.95
AK Trunnion Rivet Hole Drilling Fixture
Here is a professional tool for drilling the front and rear trunnion holes in AK47 receivers.  This tool will work with 7.62 and 5.45 trunnions...
T3-11
In Stock
 
Select an option
5MM & 7MM REAMER SET, A2-31
Quick view
$44.95
5mm & 7mm Reamer Set
 5mm and 7mm reamers for finishing the hammer and trigger holes on my flats. These will ensure that you have perfectly round holes for the axis pins to...
A2-31
In Stock
+ −

No reviews found

Customers Also Bought

AK-Builder Rail Alignment Fixture
AK-Builder Rail Alignment Fixture
$29.95
AK Center Support for 1mm Receivers
AK Center Support for 1mm Receivers
$7.00
5MM & 7MM REAMER SET, A2-31
5mm & 7mm Reamer Set
$44.95
AK47 7.62 Flat With Trunnion Holes
AK47 7.62 Flat With Trunnion Holes
$46.95
Select an option
AK-Builder AK Rivet Set
AK-Builder AK Rivet Set
$9.00
Select an option
Y & I Optional Embossing
Standard AK47 Fixed Stock 7.62 Flat
$44.95
Select an option
AK Trunnion Rivet Hole Drilling Fixture
AK Trunnion Rivet Hole Drilling Fixture
$99.95
Select an option
AK47 TRIGGER GUARD RIVETING JIG, T1-11
AK47 Trigger Guard Riveting Jig
$85.00
AK-Builder Barrel Press Kit
AK-Builder Barrel Press Kit
$139.95
Select an option
AK-Builder Rivet Tool
AK-Builder Rivet Tool
$270.00
Spot Welder Tong
Spot Welder Tong
$39.95
AK74 5.45x39 Fixed Stock Receiver Flat
AK74 5.45x39 Fixed Stock Receiver Flat
$45.95
Out-of-stock